- Front Slidermennessä antlionsopii:
- SUZUKI
Inner rod dia M6 was to small, M8 or M10 will defintely solid. As i already have front, rear and engine mount kit. "So cool in a set"Lue lisää - Rear Slidermennessä antlionsopii:
- SUZUKI
Well front slider looks cool, but inner threaded rod only M6 in diameter. If rod were M8 it will be solid. Got front, rear & engine mount, looks cool in a set.Lue lisää - Mount Slider Ver.IImennessä antlionsopii:
- SUZUKI
The product itself needlees to say, its solid and charming. Easy to install, looks cool. Gives protection to engine. Got whole set front, rear & engine mount.Lue lisää - Mount Slider Ver.IImennessä antlionsopii:
- YAMAHA
- YAMAHA
Since I have Rear Sets installed, I installed them to reduce damage when the Footpeg breaks.Lue lisää - Front Slidermennessä antlionsopii:
- HONDA CRF250L 21
[How is it used?Buy for CustomWas the one you received as per Image?YesHow was your experience with it?Satisfied[Points to note]Nut co-tightening from both sides, so a socket wrench is needed for that...Lue lisää - Rear Slidermennessä antlionsopii:
- HONDA CRF250L 21
[How is it used?Buy for CustomWas the one you received as per Image?YesHow was your experience with it?Satisfied[Points to note]Nut co-tightening from both sides, so a socket wrench is needed for that...Lue lisää - Mount Slider Ver.IImennessä antlionsopii:
- HONDA
Design is good and I bought it for Style.Although it is installation to VTR250, the hole through which Shaft passes under the front of Engine is Quantity:Pair (for Left and Right) I was able to instal...Lue lisää - Front Slidermennessä antlionsopii:
- HONDA XR250 03-
- HONDA XR250 Motard 03-
I heard that there is a case that you need to widen the bolt with a drill when you pass it through the hollow part of the Axle Shaft on the front, but in my case, it was large and strong.However, ther...Lue lisää - Front Slidermennessä antlionsopii:
- YAMAHA
- YAMAHA
I also installed this product on my wife's WR250X for Course. As it has already been installed on my 2007 WR250X, it is designed to be lightweight, simple in construction and less assertive in design,...Lue lisää - Rear Slidermennessä antlionsopii:
- YAMAHA
- YAMAHA
I also installed this one on my wife's WR250X for Course. I have already installed it on my 2007 WR250X, so I give it 100 points for its light weight, simple construction, and low self-assertion desig...Lue lisää - Rear Slidermennessä antlionsopii:
- SUZUKI
It supported me when I was standing on a slope.I think the SliderBody shaves off about 2 minutes.The Material may be softer than you think, so if you've got the speed, it's going to be aggressively cu...Lue lisää - Front Slidermennessä antlionsopii:
- SUZUKI
I think you should buy one if it will save you some money on repairs. The installation was Bolt On as well.Lue lisää - Mount Slidermennessä antlionsopii:
- SUZUKI
No problems with quality and installation.The Slider became the support against the ground firmly, and Cowl etc. of the upper part of the body were unharmed though I accidentally did a standing fall o...Lue lisää - Rear Slidermennessä antlionsopii:
- HONDA
- HONDA
I had it installed last time and loved it.A friend of mine was deprived of it because he was going to do a long distance Off-road trip in a hurry, so I bought it again and installed it for myself. (I ...Lue lisää - Rear Slidermennessä antlionsopii:
- HONDA
- HONDA
On the occasion of the forest road touring, I installed Slider though it is a part for Road.There is a possibility of getting caught and eating a high SIDE, but I want to avoid the risk of sliding and...Lue lisää - Rear Slidermennessä antlionsopii:
- YAMAHA
- YAMAHA
The antlion Rear Slider looks good - and is easy to install too with few tools required. This is not a required product to install on your supermoto setup but if you want an extra peace of mind get on...Lue lisää - Front Slidermennessä antlionsopii:
- YAMAHA
- YAMAHA
The antlion Front Slider looks good - and is easy to install too with few tools required. This is not a required product to install on your motard setup but if you want an extra peace of mind get one....Lue lisää - Mount Slider Ver2mennessä antlionsopii:
- YAMAHA SR400 (FI model)
I got an email that Engine slider for W201217A2231SR400 is out of stock from Manufacturer.I cancelled my order, but I could not execute it from the web.Lue lisää - MOTARD Mount Slidermennessä antlionsopii:
- YAMAHA
- YAMAHA
This is a 2007 WR250X with circuit running, so it was installed to protect the water pump and generator etc. Since it had already purchased the Axle Slider of Antlion at We-Big for the public road, it...Lue lisää - Mount Slider Ver.IImennessä antlionsopii:
- YAMAHA tricker XG250
The product itself was convincing in terms of quality and shape.However, it later occurred to me that the Mounting Slider would be effective when I was driving on paved roads and falling over.It doesn...Lue lisää
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING