I have been riding for about a year with the Grip set 10mm to the inside, because I wanted to respect the OEM position and wanted to know the Merit of the Taper Bar.
I was not accustomed to a flat shape with a small aperture and hanging down, and I tried a handlebar on hand and saw how it went. I chose this bar because of its more orthodox shape.
We had no problems with the installation itself in conjunction with the Conversion Adapter.
I want to make it as wide as possible, but I couldn't make it inward as much as I wanted because of the strain on the hose at the brake master. 10mm or so.
I drove about 500 km after installation, and it was nice to be able to relax and ride when the position is natural.
- Instock
18.94 EUR (3,513 JPY)
Webike Point: +35 pt
(0.18 EUR)
Toimitustiedot
In Stock : 3 left, Ships within 24 hours.
Estimated arrival date around
Asennus
HONDA
-
HORNET250
*Requires drilling of switch hole|* Requires side cap (for 18mm diameter)
-
APE 50
08-12 (drum brake) *Processing of switch holes is required
-
APE 50
-07|08 (Carburetor) *Ape 100 (09-) only, switch hole drilling required
-
APE 100
-12 (drum brakes) *Ape 100 (09-) requires drilling of switch holes
Nähdä kaikki
HONDA
YAMAHA
-
SR500
88-00 (CV cab models) *Processing of switch hole required
-
SR400
88-00 (CV cab models) *Processing of switch hole required
-
SR400
01-12 (Carburetor/FI disc brake models) *Processing of switch hole required
-
XJR400R
01-07 (RH02J)*Processing of switch hole drilling required|*Side cap required (for inner diameter 18mm)
Nähdä kaikki
YAMAHA
SUZUKI
-
GSX400
05-07 GK7CA *Processing of the switch hole is required|* You can use the normal side cap.
-
ST250 E Type
-07 (NJ4AA)(Carburetor model)*Processing of switch hole required|*You can use normal side cap.
-
ST250
-07 (NJ4AA)(Carburetor model)*Processing of switch hole required|*You can use normal side cap.
-
RV200 VANVAN
-07 NH41A Carburetor *Processing to open switch holes required|* The stock side caps can be used.
Nähdä kaikki
SUZUKI
KAWASAKI
-
ZEPHYR750
*Requires drilling of switch hole|* Requires side cap (for 18mm diameter)
-
ZEPHYR400
*Requires drilling of switch hole|* Requires side cap (for 18mm diameter)
-
ZEPHYR1100 RS
*Requires drilling of switch hole|* Requires side cap (for 18mm diameter)
-
ZEPHYR1100
*Requires drilling of switch hole|* Requires side cap (for 18mm diameter)
Nähdä kaikki
KAWASAKI
Others
Open Fit Model Information Table
-
Universal
Tuotteen kuvaus Alla on automaattisesti kääntää Google.
Tuotetiedot
Ohjaustanko Väri : Musta
[Ohjaustangon tekniset tiedot]
ohjaustanko : Teräs, musta / ulkohalkaisija Φ22.2mm / sisähalkaisija Φ18mm
On mahdollista käyttää STD-kaapelia ja letkua.
[Kahvan koko]
Kokonaiskorkeus : 80mm
Kokonaisleveys : 730mm
Pidikkeen kiinnitysosa Tehokas leveys : 130mm
Takaisinvetokoko : 110mm
Inner Angle : 21-astetta
Anteversion kulma : 85-astetta
*
* Kahvapuristin (haltija tai virka) kuvassa ei ole mukana.
* Mitatukset tehtiin tuotteen ollessa tasainen..
Napsauta MONKEY kahvan haltijaa
Napsauta muita värejä.
Normaali kädensijan koko listalle 7/8 tuuman tienmalleista.
Normaali kädensijan koko listalle 7/8 amerikkalaisille skoottereille.
Normaali kädensijan koko listalle 1 tuuman amerikkalaisille malleille..
Tehty Japanissa. Yrityksessä hallitaan prototyyppejä, asennusvahvistuksia ja tuotantoa. Huolellisesti valittuja materiaaleja taivutetaan ja hitsataan suurella tarkkuudella ja viimeistellään korkealaatuisella hioma-viimeistelyllä, joka perustuu yrityksen vuosien aikana hankkimaan tekniikkaan ja tietämykseen. Ohjaustanko on sitoutunut laatuun ja se on valmistettu STKM13A-terästä vetolujuudella. Musta kromattu materiaali on päättynyt akryylin kaksinkertaisella ruosteenpoistokäsittelyllä. Tämä tuote täyttää JMCA: n turvallisuusstandardit.
varovaisuus
* If there may be an instruction manual included, it will be written in Japanese.
NEW ARRIVALS IN USED PARTS FOR
NEW ARRIVALS IN USED PARTS FOR
NEW ARRIVALS IN USED PARTS FOR
New arrivals in used
New arrivals in used
asiakkaiden arvostelut
Reviews with image
Fits:YAMAHA XJR400R 01-07 (RH02J)*Processing of switch hole drilling required|*Side cap required (for inner diameter 18mm), YAMAHA XJR1300 07-12 (RP17J) *Processing to open switch hole required|* Required side cap (for 18mm ID), YAMAHA XJR1300 00-06 (RP03J) *Processing to open switch hole required|*Side cap required (for 18mm ID), YAMAHA TW200E 00- (Disc Brake Car) *Processing of switch hole is required, YAMAHA TW225E 00- (Disc Brake Car) *Processing of switch hole is required
Feb 27, 2025
Helpful?
Fits:YAMAHA XJR400R 01-07 (RH02J)*Processing of switch hole drilling required|*Side cap required (for inner diameter 18mm), YAMAHA XJR1300 07-12 (RP17J) *Processing to open switch hole required|* Required side cap (for 18mm ID), YAMAHA XJR1300 00-06 (RP03J) *Processing to open switch hole required|*Side cap required (for 18mm ID), YAMAHA TW200E 00- (Disc Brake Car) *Processing of switch hole is required, YAMAHA TW225E 00- (Disc Brake Car) *Processing of switch hole is required
Mar 10, 2022
Not a lot you can say about handlebars. They look good and seem to be of a high quality, time will tell. However there are a few points worth mentioning. There is a manufacturers sticker where the grip goes, and not making it an easy to remove sticker meant I took about 20 minutes soaking and rubbing the area to remove it.Also the standard bars have a location hole for the left and right switch cluster to stop them rotating. These bars do not so you either drill a hole and hope to get it in the correct position, or remove the locating pin from the switch cluster.
View Detail
Helpful?
Fits:YAMAHA XJR400R 01-07 (RH02J)*Processing of switch hole drilling required|*Side cap required (for inner diameter 18mm), YAMAHA XJR1300 07-12 (RP17J) *Processing to open switch hole required|* Required side cap (for 18mm ID), YAMAHA XJR1300 00-06 (RP03J) *Processing to open switch hole required|*Side cap required (for 18mm ID), YAMAHA TW200E 00- (Disc Brake Car) *Processing of switch hole is required, YAMAHA TW225E 00- (Disc Brake Car) *Processing of switch hole is required
Mar 3, 2022
I replaced Handlebar to immeChain.
The height of the handlebar is now much lower.
It's so much easier to ride.
Helpful?
Fits:YAMAHA XJR400R 01-07 (RH02J)*Processing of switch hole drilling required|*Side cap required (for inner diameter 18mm), YAMAHA XJR1300 07-12 (RP17J) *Processing to open switch hole required|* Required side cap (for 18mm ID), YAMAHA XJR1300 00-06 (RP03J) *Processing to open switch hole required|*Side cap required (for 18mm ID), YAMAHA TW200E 00- (Disc Brake Car) *Processing of switch hole is required, YAMAHA TW225E 00- (Disc Brake Car) *Processing of switch hole is required
Feb 23, 2021
这个车把比原厂的车把窄了不少，另外，原厂的那个车把真得好重，这个则要轻很多。然后这个车把他不像原厂的车把有往回弯的那样，所以整个骑行的姿势会往前稍稍前倾一些，而原来的姿势是直直的坐着，相比较而言我还是更喜欢这个姿势，腰部会更舒服一些。车把短了有一些别的问题，national cycle的这个挡风适配不如原来的车把好了。----------------------------------------------The handlebar is narrower than a lot of the original handlebar, in addition, that the original handlebar really well heavy, this will have a lot of light. Then the handlebar He does not have that back the original handlebar bend, the entire riding posture will move forward slightly forward for some, but the original posture is sitting straight, comparatively speaking I prefer this position, the waist will be more comfortable. There are some other short handlebar problems, national cycle of the wind adapted better to the original handlebar good.Powered by Google Translator
View DetailHelpful?
Fits:YAMAHA XJR400R 01-07 (RH02J)*Processing of switch hole drilling required|*Side cap required (for inner diameter 18mm), YAMAHA XJR1300 07-12 (RP17J) *Processing to open switch hole required|* Required side cap (for 18mm ID), YAMAHA XJR1300 00-06 (RP03J) *Processing to open switch hole required|*Side cap required (for 18mm ID), YAMAHA TW200E 00- (Disc Brake Car) *Processing of switch hole is required, YAMAHA TW225E 00- (Disc Brake Car) *Processing of switch hole is required
Jun 1, 2019
Качественный, красивый руль. Установил его вместо оригинального. Очень удобный для меня по сравнению с оригинальным. Удобнее посадка, легче и комфортней управлять байком. Минусы немного шире оригинала, тяжелее. Очень понравился руль. Рекомендую.Quality, beautiful steering wheel. Installed it instead of the original. Very convenient for me compared to the original. Comfortable fit, easier and more comfortable to drive a bike. Cons a little wider than the original, heavier. Loved the steering wheel. Recommend.translated by Google Translator
View DetailHelpful?
New Custom Articles
