[Koko]
Leveys : Noin 760mm
Pituus : Noin 500mm
Korkeus : Noin 520 mm
[Materiaali]
FRP
Tuotteen sisältö
Kopan runko, kannatin, näyttö, ruuvisarja
* Tämä koppa on ulkokäyttöön tarkoitettu yleiskäyttöinen tuote, joten siinä voi olla naarmuja, naarmuja ja hankausta jne.. reiät eivät välttämättä sovi, ja niitä on ehkä muutettava asennusta varten. Varmista, että ymmärrät seuraavat asiat ennen ostamista.
* Valoyksikkö ja koppa voivat häiritä toisiaan, jolloin kopan häiritsevä osa on poistettava.
* Haarukka ja koppa voivat häiritä toisiaan, joten sinun on tarkistettava vasemman ja oikean puolen liikealue ja ajettava koppa, jos siinä on häiriöitä.
* Muut häiritsevät osat on leikattava, ajettava tai muuten käsiteltävä.
* Erikseen myytäville kevyille yksiköille on valmistettava päävaljaiden jatkosarja.
* Reiä tuen ja kopan välillä voi siirtyä kopan asennosta riippuen. Tässä tapauksessa sinun on laajennettava kopan reikä.
* On tapauksia, joissa seula- ja kopanreiät eivät täsmää, tässä tapauksessa sinun on kiinnitettävä seula- ja kopanreiät kopan keskireikästä ulkopuolelle hyvin mutterilla ja laajennettava sitten osat, jotka eivät vastaa tiedostoa.
* Joissakin erissä ei ole reikää ruudun reunassa. Poraa siinä tapauksessa reiät, jotta ne sopivat näyttöön.
* Muita kuin tässä lueteltuja käsittelymenetelmiä ei ole saatavana, joten tarkista varsinainen ajoneuvo.
* Tuote on käsittelyssä, joten emme voi hyväksyä palautuksia kyvyttömyydestä asentaa se.
* Muista käsitellä ja asentaa tuote ennen maalaamista. Maalauksen jälkeen ei hyväksytä vaatimuksia.
* Huomaa, että tuotetiedot voivat muuttua valmistajan syystä.
[Size]
Width: Approx. 760mm
Front and rear length: Approx. 500mm
Height: Approx. 520mm
[Material]
FRP
Components
Cowl body, bracket set, windshield, windshield screw set
*Please make sure to read the notes before purchasing.
*7 inch projector LED headlight unit and the same type of light unit are used for the lights.
*Because this cowl is a universal product made non Japanese, it may have some scratches and scuffs, and the holes may not fit, so some modification is required for installation.Please make sure you understand the following information before purchasing.
*The light unit and cowl may interfere with each other, in which case it is necessary to shave the interfering part of the cowl.
*There is a case that the fork and the cowl interfere with each other, check the range of movement of both sides and if it interferes, it is necessary to shave the cowl.
*Other interfering parts need to be cut or shaved.
*For light units sold separately, it is necessary to make an extension harness from the main harness.
*Depending on the positioning of the cowl, the hole between the bracket and the cowl may be misaligned.To do this, you will need to widen the hole in the cowl.
*In some cases, the holes of the windshield and the cowl do not match, in that case, you need to fix the windshield with the well nut from the center hole of the cowl to the outside, and widen the holes with a file in order.
*Depending on the lot, some of them do not have the hole for the windshield on the cowl side.In this case, please drill the holes in order to match the windshield.
We will not provide information about processing methods other than those mentioned here, so please verify according to your actual bike.
*Any returns will not be accepted due to inability to install the product.
*Please be sure to process and install before painting.Any claims after painting are not accepted.
*There may be changes in product specifications due to the manufacturer's reasons.