Väri: Musta anodisoitu
Suurin takapyörän säde
+ 6 cm = 225 mm
+ 12 cm = 250 mm
+ 16 cm = 270 mm
+ 20 cm = 305 mm
Takajousituksen asennusasento
+ 6 cm = 245 mm
+ 12 cm / + 16 cm / + 20 cm = 310 mm
Lisävarusteet: M12 Pitkä akseli, L = 290 mm
Valmistava yritys: KEPSPEED
Alkuperämaa: Kiina
* Mukana M12-pitkäakselinen akseli L = 290mm. Varastopituisia akseleita ei voida käyttää.
* Ketjusäädin ja jalustakoukku, titaanivärinen.
[Asennus]
* Tämä kääntövarsi on suunniteltu käytettäväksi ilman säätöä, kun sitä käytetään täydellisessä sarjassa.
* Huomaa, että se ei ole tarkistanut yhdistelmän yhdenmukaistamista muiden yrityksen tuotteiden kanssa, joten ole hyvä ja hyväksy se.
* Ole valmis kokoontumaan, jos se kokenut moottoripyörän huoltoa.
* Vetoketjun runkojen määrä vaihtelee asiakkaan ajoneuvon kunnon sekä etu- ja takarattaiden mukaan, joten GM-MOTO ei tarjoa tietoja tästä.
* Varmista, että onko epänormaalia kosketuspistettä, vaikka takajousitus on kokonaan alhaalla.
* Suorita prosessi, jolla pienennät aukkoa aluslevyllä, jos kehyksen ja tämän kääntövarren välillä on vähintään 0,5 mm: n rako.
* Se voi vahingoittaa pahinta tapausta, jos nivelakseli kiristyy, kun tilavuus on suuri, suurta kuormitusta voidaan käyttää kääntövarsiin.
* On mahdollista, että kunkin tuotteen yksityiskohtaisessa osassa on pieni muutos. On kohta, joka eroaa hieman johdantokuvasta, mutta annan etusijan varsinaiseen asiaan, joten ymmärrä, kiitos.
* Etsimme moottoripyörien huoltoteknikkoa suorittamaan kokoonpanotyöt moottoripyörien huoltoasiantuntijoista.
* Huomioi niin sanotun "alkulähteen" esiintyminen käynnistyksen jälkeen, tee usein tarkastuksia, jotta ei aiheuta odottamattomia ongelmia.
* Kuva voi sisältää muita tuotteita.
* Huomaa, että tuote-eritelmä voi muuttua valmistajan syistä.
■Color: Black Anodized Aluminum
■Maximum rear wheel radius
+6cm = 225mm
+12cm = 250mm
+16cm = 270mm
+20cm = 305mm
■Rear suspension installation position
+6cm = 245mm
+12cm / +16cm / +20cm = 310mm
■Components: M12 Long Axle Shaft L=290mm
■Manufacturing company: KEPSPEED
■Country of origin: China
[Notes on purchase]
*All GM-MOTO products are custom parts.Since these products are set up in response to the requests of heavy users, there may be parts of the product that change or decrease from the original driving performance.Please use as dress-up parts for show model machines.Therefore, it is not suitable for driving on public roads or tracks.In some cases, it may not be possible to mount the unit on a motorcycle, or adjustments and modifications may be required in various areas.
*M12 Long Axle Shaft L = 290mm is included.Stock length axle shafts cannot be used.
*Chain adjuster and stand hook in titanium color.
[About the installation]
*This swingarm is designed to be used without adjustment when the complete kit is used.
※GM-MOTO has not verified the consistency of the combination with other companies' products.
*Please make sure that the person with experience in motorcycle maintenance performs the assembly work.
*The number of tentioners of the drive chain varies depending on the condition of the customer's vehicle and the front and rear sprockets, so GM-MOTO does not provide information on this.
*Even if the rear suspension is at full bottom, make sure to check for any abnormal contact points before riding.
*If the gap between the frame and the swingarm is more than 0.5mm on each side, please use washers to reduce the gap.
*If the pivot shaft is tightened with a large gap, the swingarm will be subjected to a high load and may be damaged in the worst case.
※There may be some minor specification changes for each product.There may be some points that differ slightly from the introduction image.
*Please have assembly work done in a specialist shop regarding motorcycle maintenance.
※After the start of riding, pay attention to the occurrence of so-called initial loosening and perform frequent inspections to prevent unexpected problems.
*The image may include other products.
*There may be changes in product specifications due to the manufacturer's reasons.
*Because it is made overseas, the molding, welding, painting, etc. may be insufficient.There may be some minor scratches and scuffs due to transportation problems.