[Materiaali] Chromoly Steel (3-kerroksinen pinnoite)
* Tuotespesifikaatioissa saattaa olla muutoksia valmistajan syistä.
[Tietoja asennuksesta]
*Akseliakselit ovat tärkeitä osia.
Asennuksen saa suorittaa pätevä henkilöstö ammattiliikkeessä.
・Käytä akselin pään muotoon sopivaa työkalua.
Jos akselia kiristetään sopimattomalla työkalulla, akselin pinnalla oleva pinnoituskalvo naarmuuntuu ja syntyy ruostetta.
・Ennen asennusta voitele akselin pintaan rasvaa tai muuta öljyä.
Akselin pinta on käsitelty KOODin alkuperäisellä "3-kerroksisella pinnoituskalvolla", joten ruostetta ei tapahdu itse akseliin normaalikäytössä. Tarkoituksena on estää ruosteen siirtyminen pyörän laakereista jne., joka johtuu metallien potentiaaliero.
・Noudata valmistajan ilmoittamaa kiristysmomenttia.
・Jos ajoneuvo on asennettu pohjamutterilla, tarkista mutteri.
Jos mutteri vaurioituu kaatuessa jne. tai jos itselukittuva osa on kulunut, muista käyttää uutta mutteria. Tämä estää akselin kierteiden vaurioitumisen.
[Tuotteen laadusta]
・KOOD on ryhtynyt kaikkiin mahdollisiin toimenpiteisiin tuotannon ohjaamiseksi. Jos kuitenkin ilmenee ongelmia, ota yhteyttä KOODiin ennen töiden aloittamista.
*KOOD ei missään tapauksessa hyväksy vaatimuksia tai palautuksia asennuksen jälkeen (kuten pujottaa akseli pyörään).
· Ruosteesta
KOOD-akselit on käsitelty "3-kerroksisella pinnoituskalvolla".
Se on käsitelty normaalia pinnoituskalvoa vahvemmalla kalvolla. Ruostetta saattaa esiintyä käyttöolosuhteista riippuen, mutta laadussa ei ole ongelmaa.
· Siirtynyt ruoste : Ulkopuolelta ruostetta pääsee pinnoitetulle pinnalle
・ Pinnoitekalvon vaurioituminen.. Työkalujen väärä käyttö, lentävät kivet ratsastuksen aikana, putoaminen jne.
[Huomio]
Pinnoitetuilla muttereilla varustetuissa KOOD-akseleissa tapahtuu usein kierteiden vaurioitumista asennuksen aikana.
Pinnoituksen luonteesta johtuen tämä näkyy usein, kun pinnoitetut osat (esim. KOOD-akseli ja KOOD-mutteri) verkottuvat keskenään tai kun kierteitetty osa on rasvaton.
Käytä ruosiosassa korroosionestorasvaa, kuten kelkka-ainetta, kun asennat sen.
[Material] Chromoly steel (3-layer plating finish)
*There may be changes in product specifications due to the manufacturer's reasons.
[About the installation]
*Axle shafts are critical parts.
Installation must be carried out by qualified personnel at a professional shop.
・Please use the appropriate tool for the head shape of the shaft.
If the shaft is tightened with an inappropriate tool, the plating film on the shaft surface will be scratched and rust will be caused.
・Before installation, apply grease or other oil to the shaft surface.
The surface of the shaft is treated with KOOD's original "3-layer plating film", so rust will not occur on the shaft itself under normal use.The purpose is to prevent rust transfer from wheel bearings, etc., which is caused by the potential difference of metals.
・Please observe the tightening torque specified by the manufacturer.
・If the vehicle is installed using the stock nut, please check the nut.
If the nut is damaged by tipping over, etc., or if the self-locking part is worn out, be sure to use a new nut.This is to prevent damage to the shaft threads.
[About Product Quality]
・KOOD has taken all possible measures to manage the production. However, if there is any problem, please contact KOOD before the work.
*In no event will KOOD accept any claims or returns after the installation (such as threading the shaft into the wheel).
・About rust
KOOD shafts are treated with a "3-layer plating film".
It is processed with a stronger film than normal plating film.Rust may occur depending on the usage conditions, but there is no problem with the quality.
・Transferred rust: Rust from the outside gets on the plated surface
・Damage to the plating film... Improper use of tools, flying rocks during riding, falls, etc.
[Caution]
In case of KOOD shafts with plated nuts, damaging the threads during installation often happens.
Due to the nature of plating, this is often seen when the plated parts (e.g. KOOD shaft and KOOD nut) mesh with each other or when the threaded part is greaseless.
Please use an anti-corrosive grease such as sledge compound on the screw part when you install it.